TRAYNOR K4TRAY Details top
The K4 is an advanced, extremely versatile stereo keyboard amplifier that delivers a wide spectrum of tones. More importantly, it has the ability to sound right with a minimum amount of tweaking.
The K4 consists of three separate, built-in amplifiers, for true stereo operation with a mono-summed woofer. A 200-watt Low Frequency amplifier drives a 12-inch, 200-watt woofer, while a pair of 50 watt amps drive the left and right channels, delivering the mid and high frequencies through a set of 4.5-inch, 30-watt midrange drivers and a pair of 20-watt 2.5-inch compression drivers with horns.
One unique feature of the K4 is how Channel 1 utilizes a pair of 12AX7 tubes, one for each channel, left and right. These preamp tubes supply warmth and smooth out the harsh harmonic overtones often associated with many modern Digital keyboards. It also excels at maintaining the warmth and character of vintage synthesizers and organs where it isn’t always practical to use the much larger powered speaker cabinets they are typically associated with.
There is also a select switch to toggle between using either the tube or a Solid-State signal path, bypassing the tube on the input altogether, for those times when the cleanest signal path possible is preferred. Channel one also features a foot switchable Tube Overdrive control, for those who like to add a small amount of grit to their playing. Depending on the level, a small amount of warmth right up to full grit can be had from the Tube Overdrive. Natural tube compression is a very desired tone as the subtle dynamics can't be properly emulated by most of today’s digital workstations. Use this feature to add some grit to an otherwise sterile keyboard tone to make it a truly vintage, tube-based one. A single button latching footswitch, like our AFS-1 can be used to engage the Lead/Overdrive feature. If a footswitch is connected, it will disable the front panel switch. Additional tonal control can be had thanks to the three band EQ and 5 position (Bypass, Studio, Live, Piano, Organ) selectable voicing presets.
Like Channel One, Channel Two also features its’ own Gain control as well as a 3 band EQ. Available inputs include a stereo pair of balanced 1/4-inch TRS inputs and a single XLR, for mono only operation.
Channel Three utilizes an independent Gain control to set the levels for the stereo pair of balanced 1/4-inch TRS inputs and stereo pair of RCA inputs. All three channels feature their own input clip LED’s for simple monitoring of input levels from the darkest of stages and a single Master Volume and Power Switch let you be heard when you want to.
Channel 4 inputs and Gain control can be found on the rear panel. The possibilities are endless with it. Use it to bring in an external click track or drum monitor mix, or get a microphone feed from the FOH or monitor console. The two inputs can even be used for monitoring two different sources if desired. The signal goes directly into the power amplifier, so it bypasses the Master Volume and Line Outs entirely.
Features
Front Panel
A Master Volume control is located on the front panel along with the Power switch and LED.
Front panel controls for Channel 1 include:
Two parallel pairs of balanced 1/4-inch TRS inputs for mono or stereo operation
Gain, Bass, Mid, Treble controls with a boost/cut of 15db
A five position voicing selector (Bypass, Studio, Live, Piano, Organ)
Tube/Solid State input switch
Lead Level control
Overdrive Trim control
Lead Bypass switch
Input clip LED
Front panel controls for Channel 2 include:
Parallel pair of balanced XLR (mono only) and stereo balanced 1/4-inch TRS inputs for mono or stereo operation
Gain, Bass, Mid, Treble controls
Input clip LED
Front panel controls for Channel 3 include:
Gain control
Parallel pair of unbalanced RCA and stereo balanced 1/4-inch TRS inputs for mono or stereo operation
Input clip LED
Rear panel
Channel 4 Monitor
Channel 4 has been added as an extra channel for monitoring purposes, the signal does not mix in with the Main stereo bus and thus the Line Out is not affected by it. The input has it own level control. The left and right inputs can even be used as two separate monitoring sources and the signal goes directly into the amplifiers, bypassing the master volume entirely.
Rear panel controls for Channel 4 include:
Gain control
Stereo balanced 1/4-inch TRS inputs for mono or stereo operation
Subwoofer Out
Subwoofer out is provided via a TRS 1/4-inch jack. This mono signal features no filtering, so it can be used to feed a powered sub, remote powered speakers or any other device requiring a mono-summed Full range signal.
Balanced Stereo XLR Line Outs
These are used to connect directly to a mixing console, or for direct recording. The Line Out jacks are Pre-Master control, turning the Master control up or down will not have any affect on the level of the Line Out jacks.
Ground Lift
The ground lift switch is located beside the XLR jacks. It lifts the balanced Line out ground (Pin 1) when pushed in.
Footswitch Jack
When used in conjunction with any single button latching footswitch, like our AFS-1, the Tube Overdrive mode can be activated or deactivated remotely at will.
Cooling system
Two 3-inch fans cool the K4, The fans, normally operate at a low speed, the speed increases depending on how hard the amplifier is working. The air intake vent is located at the top of the cabinet and the exhaust vents are located at the front and back of amplifier.
Caution: The top vent must be kept clear in order for the air to enter into the amplifiers. The rear and front vents are used to allow the warm air out of the unit.
Head Phone Jack
A 1/4-inch headphone jack is provided on the rear panel as well. When the jack is used, it mutes the signal that comes out of the amplifier, with the exception of the monitor channel 4.
Traynor Keyboard Amps Series Overview
Traynor backline amplification is designed and built using unparalleled levels of durability and quality found only from the name legendary for its reliability and toughness. Inside every amplifier we use high-grade glass epoxy circuit boards, low-noise metal film resistors, phone jacks with gold plated contacts, chassis metal which is one to two gauges thicker than the competition’s and durable plywood construction.
Outside you will find curved, heavy gauge, perforated metal speaker grilles, rugged black leatherette covering and convenient carry handles. Add rigorous factory testing and our unbeatable two year (even if you break it) unlimited transferable warranty* and you can be sure you''ve got what you need to reliably sound your best for many years to come.
Low distortion at high sound pressure levels
Rock solid plywood construction with rigid internal bracing
Curved, perforated 16 gauge, black painted metal grilles
Black leatherette covering and non-slip rubber feet
Low profile, integral bar handles
Thermal bias sensing protection
XLR, RCA and 1/4" phone jacks with gold-plated contacts
Active filtering circuits for simple, yet effective tonal shaping
High-grade glass epoxy circuit boards and low noise components
Chassis metal one to two gauges thicker than the competition’s
Loaded with high quality, custom-design speakers
Consistent box to box production using advanced quality assurance methodology & CAD/CAM technology
Two year (even if you break it) unlimited transferable warranty*
Zoom / More pics 
Print this Page 
Gifts 
Details 
Specs 
Documentation 
More Pics 
Warranty 
Accessories 
