Crown XTi1002 Power Amplifier
XTI1002
Overview Features Specs More Info
Features
- Peakx Plus Limiters provide the ultimate in system performance and
protection by allowing full control over threshold, attack, and release
- Enhanced Subharmonic Synth section provides user control over frequency, gain
and filter type for system-specific tuning
- 3 User-defined fan mode controls normal, early and fullspeed for matching
fan performance to a specific application
- New system monitoring provides software visibility of AC line voltage and power
supply temperature
- Integrated cast-aluminum handles for easy handling and enhanced durability
- Locking power cord clip provides a secure connection between the amplifier and
power cord
- Updated HiQnet System Architect control software
- Increased number of presets to a total of 50; 49 of which are user definable
Specs
Integrated Processing
|
Input EQ
|
6 parametric filters per channel with adjustable Q, 15 dB
boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ
section can be bypassed.
|
|
Crossover Filters
|
Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB
per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes 15 dB bandpass
gain and polarity control.
|
|
Output EQ
|
8 parametric filters per channel with adjustable Q, 15 dB
boost/cut. This 8-filter EQ section can be bypassed.
|
|
Delay
|
For signal alignment of driver; 50 mS of total delay.
|
|
SubHarmonic Synth
|
Takes the low-frequency content of the input signal and "synthesizes" a new
signal that is the same as the input signal but one octave lower. The new
synthesized signal is then mixed with the original signal to create the effect.
New: Users now have control over frequency, gain, and filter type.
|
|
Peakx Plus Limiter
|
User defeatable limiter that allows users to control
Threshold, Attack, and Release times.
|
|
Presets
|
50 total presets, 49 of which are user-definable.
|
Preformance
|
Sensitivity (for full rated power at 4 ohms)
|
1.4 Vrms
|
|
Frequency Response (at 1 watt, 20 Hz - 20 kHz)
|
+0 dB, 1 dB
|
|
Signal-to-Noise Ratio (below rated 1kHz power at 8
ohms)
|
XTi1002/2002/4002: 100 dB (A weighted)
XTi6002: 103 dB (A weighted)
|
|
Total Harmonic Distortion (THD)
|
< 0.5%
|
|
Damping Factor 20 Hz to 1 kHz
|
> 500
|
|
Crosstalk (below rated power)
|
20 kHz - 1 kHz: > 70 db
|
|
Input Impedance (nominal)
|
20k ohms balanced, 10k ohms unbalanced
|
|
Maximum Input Signal
|
+22 dBu typical
|
|
AC Line Voltage and Frequency Configurations
|
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
|
|
AC Line Current
(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch)
|
XTi1002: 6.8A; no more than 38W at idle
XTi2002: 8.3A; no more than 38W at idle
XTi4002: 10.5A; no more than 38W at idle
XTi6002: 15.3A; no more than 180W at idle
|
|
Operating Temperature
|
0C to 40C at 95% relative humidity (non-condensing)
|
Controls
|
Level
|
Two front-panel rotary level controls, one for each channel
|
|
Power Switch
|
On/Off switch applies AC power to the amplifier
|
|
Sel/Prev/Next Buttons
|
Three buttons near the LCD screen that are used to access
menu items and front panel lockout
|
|
LCD Screen
|
Backlit liquid crystal display that shows preset and processing status
|
Indicators
|
Signal Indicator
|
Green LED, one per channel, illuminates when a very
low-level signal is present at input (may be used for troubleshooting cable
runs).
|
|
10 Indicator
|
Green LED flashes when output signal exceeds -10 dB below
clip.
|
|
20 Indicator
|
Green LED flashes when output signal level exceeds -20 dB
below clip.
|
|
Ready Indicator
|
Green LED, one per channel, illuminates when the amplifier is ready to produce
audio.
|
|
Clip Indicator
|
Red LED, one per channel, turns on at the threshold of audible distortion
|
|
Temp Indicator
|
Red LED, one per channel, illuminates under excessive
temperature conditions
|
|
Power Indicator
|
Blue LED illuminates when the amplifier has been turned on and has power
|
Input/Output Connectors
|
Input Connectors
|
XLR, one per channel
|
|
Link/Out Connector
|
Loop-thru signal from input connector for linking another
amplifier, one per channel.
|
|
Output Connectors
|
Two Neutrik SpeakonNL4MP output connectors. Channel-1
Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single
4-conductor cable. Two binding post outputs (in parallel with Speakon
connectors).
|
|
HiQnet USB Connector
|
Type B, connects to HiQnet network.
|
Construction
|
Chassis
|
Steel
|
|
Front Panel
|
Cast-aluminum
|
|
Cooling
|
Proportional speed fan with front-to-rear airflow.
|
|
Dimensions
|
XTi 1002/2002/4002: 19" (W) x 3.5" (H) x 12.25" (D)
XTi 6002: 19" (W) x 3.5" (H) x 16.2" (D)
|
|
Net Weight
|
XTi 1002/2002/4002: 18.5 lbs (8.4kg)
XTi 6002: 24.0 lbs (10.9kg)
|
|
Shipping Weight
|
XTi 1002/2002/4002: 21.5 lbs (9.8kg)
XTi 6002: 30.0 lbs (13.6kg)
|
More Info
Click here for Comparison Chart and Amplifier Specs (pdf)
OverviewCrown XTi1002 Power Amplifier
Crown introduces the new XTi 1002. It is part of the new XTi2 series of power amplifiers.
The series consists of four models,
the
Crown XTi1002,
the
Crown XTi2002,
the
Crown XTi4002
and the
Crown XTi6002. These new amps have several innovative features such as Integrated Processing, enhanced efficiency,
and more power for the buck.as well as updated HiQnet sytem software. Read on for all the specs.
Features
- Peakx Plus Limiters provide the ultimate in system performance and
protection by allowing full control over threshold, attack, and release
- Enhanced Subharmonic Synth section provides user control over frequency, gain
and filter type for system-specific tuning
- 3 User-defined fan mode controls normal, early and fullspeed for matching
fan performance to a specific application
- New system monitoring provides software visibility of AC line voltage and power
supply temperature
- Integrated cast-aluminum handles for easy handling and enhanced durability
- Locking power cord clip provides a secure connection between the amplifier and
power cord
- Updated HiQnet System Architect control software
- Increased number of presets to a total of 50; 49 of which are user definable
Specs
Integrated Processing
|
Input EQ
|
6 parametric filters per channel with adjustable Q, 15 dB
boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ
section can be bypassed.
|
|
Crossover Filters
|
Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB
per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes 15 dB bandpass
gain and polarity control.
|
|
Output EQ
|
8 parametric filters per channel with adjustable Q, 15 dB
boost/cut. This 8-filter EQ section can be bypassed.
|
|
Delay
|
For signal alignment of driver; 50 mS of total delay.
|
|
SubHarmonic Synth
|
Takes the low-frequency content of the input signal and "synthesizes" a new
signal that is the same as the input signal but one octave lower. The new
synthesized signal is then mixed with the original signal to create the effect.
New: Users now have control over frequency, gain, and filter type.
|
|
Peakx Plus Limiter
|
User defeatable limiter that allows users to control
Threshold, Attack, and Release times.
|
|
Presets
|
50 total presets, 49 of which are user-definable.
|
Preformance
|
Sensitivity (for full rated power at 4 ohms)
|
1.4 Vrms
|
|
Frequency Response (at 1 watt, 20 Hz - 20 kHz)
|
+0 dB, 1 dB
|
|
Signal-to-Noise Ratio (below rated 1kHz power at 8
ohms)
|
XTi1002/2002/4002: 100 dB (A weighted)
XTi6002: 103 dB (A weighted)
|
|
Total Harmonic Distortion (THD)
|
< 0.5%
|
|
Damping Factor 20 Hz to 1 kHz
|
> 500
|
|
Crosstalk (below rated power)
|
20 kHz - 1 kHz: > 70 db
|
|
Input Impedance (nominal)
|
20k ohms balanced, 10k ohms unbalanced
|
|
Maximum Input Signal
|
+22 dBu typical
|
|
AC Line Voltage and Frequency Configurations
|
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
|
|
AC Line Current
(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch)
|
XTi1002: 6.8A; no more than 38W at idle
XTi2002: 8.3A; no more than 38W at idle
XTi4002: 10.5A; no more than 38W at idle
XTi6002: 15.3A; no more than 180W at idle
|
|
Operating Temperature
|
0C to 40C at 95% relative humidity (non-condensing)
|
Controls
|
Level
|
Two front-panel rotary level controls, one for each channel
|
|
Power Switch
|
On/Off switch applies AC power to the amplifier
|
|
Sel/Prev/Next Buttons
|
Three buttons near the LCD screen that are used to access
menu items and front panel lockout
|
|
LCD Screen
|
Backlit liquid crystal display that shows preset and processing status
|
Indicators
|
Signal Indicator
|
Green LED, one per channel, illuminates when a very
low-level signal is present at input (may be used for troubleshooting cable
runs).
|
|
10 Indicator
|
Green LED flashes when output signal exceeds -10 dB below
clip.
|
|
20 Indicator
|
Green LED flashes when output signal level exceeds -20 dB
below clip.
|
|
Ready Indicator
|
Green LED, one per channel, illuminates when the amplifier is ready to produce
audio.
|
|
Clip Indicator
|
Red LED, one per channel, turns on at the threshold of audible distortion
|
|
Temp Indicator
|
Red LED, one per channel, illuminates under excessive
temperature conditions
|
|
Power Indicator
|
Blue LED illuminates when the amplifier has been turned on and has power
|
Input/Output Connectors
|
Input Connectors
|
XLR, one per channel
|
|
Link/Out Connector
|
Loop-thru signal from input connector for linking another
amplifier, one per channel.
|
|
Output Connectors
|
Two Neutrik SpeakonNL4MP output connectors. Channel-1
Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single
4-conductor cable. Two binding post outputs (in parallel with Speakon
connectors).
|
|
HiQnet USB Connector
|
Type B, connects to HiQnet network.
|
Construction
|
Chassis
|
Steel
|
|
Front Panel
|
Cast-aluminum
|
|
Cooling
|
Proportional speed fan with front-to-rear airflow.
|
|
Dimensions
|
XTi 1002/2002/4002: 19" (W) x 3.5" (H) x 12.25" (D)
XTi 6002: 19" (W) x 3.5" (H) x 16.2" (D)
|
|
Net Weight
|
XTi 1002/2002/4002: 18.5 lbs (8.4kg)
XTi 6002: 24.0 lbs (10.9kg)
|
|
Shipping Weight
|
XTi 1002/2002/4002: 21.5 lbs (9.8kg)
XTi 6002: 30.0 lbs (13.6kg)
|
More Info
Click here for Comparison Chart and Amplifier Specs (pdf)
Features
- Peakx Plus Limiters provide the ultimate in system performance and
protection by allowing full control over threshold, attack, and release
- Enhanced Subharmonic Synth section provides user control over frequency, gain
and filter type for system-specific tuning
- 3 User-defined fan mode controls normal, early and fullspeed for matching
fan performance to a specific application
- New system monitoring provides software visibility of AC line voltage and power
supply temperature
- Integrated cast-aluminum handles for easy handling and enhanced durability
- Locking power cord clip provides a secure connection between the amplifier and
power cord
- Updated HiQnet System Architect control software
- Increased number of presets to a total of 50; 49 of which are user definable
Specs
Integrated Processing
|
Input EQ
|
6 parametric filters per channel with adjustable Q, 15 dB
boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ
section can be bypassed.
|
|
Crossover Filters
|
Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB
per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes 15 dB bandpass
gain and polarity control.
|
|
Output EQ
|
8 parametric filters per channel with adjustable Q, 15 dB
boost/cut. This 8-filter EQ section can be bypassed.
|
|
Delay
|
For signal alignment of driver; 50 mS of total delay.
|
|
SubHarmonic Synth
|
Takes the low-frequency content of the input signal and "synthesizes" a new
signal that is the same as the input signal but one octave lower. The new
synthesized signal is then mixed with the original signal to create the effect.
New: Users now have control over frequency, gain, and filter type.
|
|
Peakx Plus Limiter
|
User defeatable limiter that allows users to control
Threshold, Attack, and Release times.
|
|
Presets
|
50 total presets, 49 of which are user-definable.
|
Preformance
|
Sensitivity (for full rated power at 4 ohms)
|
1.4 Vrms
|
|
Frequency Response (at 1 watt, 20 Hz - 20 kHz)
|
+0 dB, 1 dB
|
|
Signal-to-Noise Ratio (below rated 1kHz power at 8
ohms)
|
XTi1002/2002/4002: 100 dB (A weighted)
XTi6002: 103 dB (A weighted)
|
|
Total Harmonic Distortion (THD)
|
< 0.5%
|
|
Damping Factor 20 Hz to 1 kHz
|
> 500
|
|
Crosstalk (below rated power)
|
20 kHz - 1 kHz: > 70 db
|
|
Input Impedance (nominal)
|
20k ohms balanced, 10k ohms unbalanced
|
|
Maximum Input Signal
|
+22 dBu typical
|
|
AC Line Voltage and Frequency Configurations
|
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
|
|
AC Line Current
(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch)
|
XTi1002: 6.8A; no more than 38W at idle
XTi2002: 8.3A; no more than 38W at idle
XTi4002: 10.5A; no more than 38W at idle
XTi6002: 15.3A; no more than 180W at idle
|
|
Operating Temperature
|
0C to 40C at 95% relative humidity (non-condensing)
|
Controls
|
Level
|
Two front-panel rotary level controls, one for each channel
|
|
Power Switch
|
On/Off switch applies AC power to the amplifier
|
|
Sel/Prev/Next Buttons
|
Three buttons near the LCD screen that are used to access
menu items and front panel lockout
|
|
LCD Screen
|
Backlit liquid crystal display that shows preset and processing status
|
Indicators
|
Signal Indicator
|
Green LED, one per channel, illuminates when a very
low-level signal is present at input (may be used for troubleshooting cable
runs).
|
|
10 Indicator
|
Green LED flashes when output signal exceeds -10 dB below
clip.
|
|
20 Indicator
|
Green LED flashes when output signal level exceeds -20 dB
below clip.
|
|
Ready Indicator
|
Green LED, one per channel, illuminates when the amplifier is ready to produce
audio.
|
|
Clip Indicator
|
Red LED, one per channel, turns on at the threshold of audible distortion
|
|
Temp Indicator
|
Red LED, one per channel, illuminates under excessive
temperature conditions
|
|
Power Indicator
|
Blue LED illuminates when the amplifier has been turned on and has power
|
Input/Output Connectors
|
Input Connectors
|
XLR, one per channel
|
|
Link/Out Connector
|
Loop-thru signal from input connector for linking another
amplifier, one per channel.
|
|
Output Connectors
|
Two Neutrik SpeakonNL4MP output connectors. Channel-1
Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single
4-conductor cable. Two binding post outputs (in parallel with Speakon
connectors).
|
|
HiQnet USB Connector
|
Type B, connects to HiQnet network.
|
Construction
|
Chassis
|
Steel
|
|
Front Panel
|
Cast-aluminum
|
|
Cooling
|
Proportional speed fan with front-to-rear airflow.
|
|
Dimensions
|
XTi 1002/2002/4002: 19" (W) x 3.5" (H) x 12.25" (D)
XTi 6002: 19" (W) x 3.5" (H) x 16.2" (D)
|
|
Net Weight
|
XTi 1002/2002/4002: 18.5 lbs (8.4kg)
XTi 6002: 24.0 lbs (10.9kg)
|
|
Shipping Weight
|
XTi 1002/2002/4002: 21.5 lbs (9.8kg)
XTi 6002: 30.0 lbs (13.6kg)
|
More Info
Click here for Comparison Chart and Amplifier Specs (pdf)
Sale Price: $499.00 MSRP: $998.00 You Save: $499.00 (50%)!
Contact Us for More Information
You might also like:
Customer Reviews:
Our Happy Customers "Hang on to Bob Chapman. I called with a couple questions and he sold me a Martin guitar. He was very helpful and struck me as sincere and credible (for a musician). Well done."
more...
|
Print this Page 
