QSC RMX5050 1050 Watt Amp

QSC RMX5050 Details

QSC's RMX 5050 power amplifier represents the state-of-the-art in professional quality performance at an affordable price. Perfectly suited for a wide range of sound reinforcement applications including professional touring, performing musicians, and mobile entertainers, the RMX 5050 is optimized to deliver high levels of sustained power, extraordinary audio performance and road-proven reliability.

Like its smaller sibling (the RMX 4050HD), the RMX 5050 features a three-tier, Class H design. The RMX 5050 is extremely efficient at real world power levels. Less AC current is wasted and more goes into producing useful audio power. The RMX 5050 uses the best available component upgrades to increase peak power by 25% over the RMX 4050HD.

Like all RMX amps, the RMX 5050 features balanced 1/4" TRS, XLR and barrier strip inputs, binding posts and Neutrik Speakon™ outputs, front-mounted gain controls, plus signal and clip LED indicators to monitor performance.

FEATURES

• The new flagship of the RMX line, the RMX 5050 provides extremely high power and represents tremendous value
• The RMX 5050 provides advanced thermal performance, delivering higher continuous power in 2-ohms stereo or 4-ohms bridged applications
• Dual mono, high current power supply for increased reliability and performance
• 3RU chassis only 16" deep
• Professional quality performance—incorporates road-proven QSC designs
• High-current toroidal transformers for greater two-ohm power and low noise
• Independent user-defeatable clip limiters reduce distortion
• Selectable low-frequency filters (30 Hz or 50 Hz) protect speakers and increase headroom
• Balanced 1/4" (6.3 mm) TRS, XLR, and barrier strip inputs for maximum flexibility
• Binding post and Neutrik Speakon™ outputs
• Front mounted gain controls for easy access
• Signal and Clip LED indicators to monitor performance
• 3-year warranty. An optional 3-year extended service contract is available. Ask your dealer for details.

RMX 5050 AMPLIFIER
STEREO MODE, Both Channels Driven
8 ohms FTC 20 Hz-20 kHz 0.1% THD	1050 Watts
4 ohms FTC 20 Hz-20 kHz 0.1% THD	1600 Watts
2 ohms FTC 20 Hz-20 kHz 0.1% THD	2000 Watts
8 ohms EIA 1 kHz 0.1% THD	1100 Watts
4 ohms EIA 1 kHz 0.1% THD	1800 Watts
2 ohms EIA 1 kHz 1% THD	2500 Watts
BRIDGE-MONO MODE
8 ohms FTC 20 Hz-20 kHz 0.1% THD	3200 Watts
8 ohms EIA 1 kHz 0.1% THD	3600 Watts
4 ohms EIA 1 kHz 1% THD	5000 Watts
Distortion (SMPTE-IM)	Less than 0.02%
Distortion (Typical) 20 Hz-20 kHz: 10 dB below rated power 1 kHz and below: full rated power	Less than 0.02% Less than 0.02%
Frequency Response	20 Hz to 20 kHz, 8 ohms, LF filter bypassed, +0/-1 dB 5 Hz to 50 kHz, 8 ohms, LF filter bypassed, +0/-3 dB
Damping Factor	Greater than 250 @ 8 ohm
Noise (unweighted)	100 dB below rated output (20 Hz to 20 kHz, 8 ohm load)
Input Sensitivity	1.42 Vrms for 1050 watts into 8 ohms
Controls Front: Controls Rear:	AC power switch, Ch. 1 and Ch. 2 gain control 10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel.
Voltage Gain	64x (36 dB) for 8 ohm load
Input Impedance	20 k ohm balanced, 10 k ohm unbalanced
Indicators	Power-On: Green LED, Protect: Red LED Signal -30dB: Yellow LED, Clip: Red LED
Connectors Input: Connectors Output:	XLR female, TRS (1/4-inch), and barrier-strip screw terminals, each channel Binding posts and Speakon outputs (Ch. 1 Speakon wired for biamp)
Cooling	Continuously variable-speed fan, rear-to-front air flow
Amplifier Protection	Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads
Load Protection	On/off muting, DC fault output crowbar
Power Requirements	100, 120 or 240 Volts AC (±10%) 50-60 Hz (factory configured)120V models require 20 Amp, 120V service and are supplied with a NEMA 5-20 plug on the cordset.
Dimensions	19" 19.0" (48.3 cm) wide, 5.25" (13.3 cm) tall, 15.9" (40.39 cm) overall depth
Weight	75 lb (34.02 kg) net, 87 lb (39.46 kg) shipping
All Specification Subject to Change Without Notice.

QSC RMX5050 Specs

QSC RMX5050 Stereo Power Amplifier (5,000 Watts)

Stereo Mode (both channels driven)

8 ohms (FTC 20 Hz - 20 kHz 0.1% THD): 1050 Watts Continuous Average Output Power Per Channel
4 ohms (FTC 20 Hz–20 kHz 0.1% THD): 1600 Watts Continuous Average Output Power Per Channel
2 ohms (FTC 20 Hz–20 kHz 0.1% THD): 2000 Watts Continuous Average Output Power Per Channel
8 ohms EIA 1 kHz 0.1% THD): 1100 Watts Continuous Average Output Power Per Channel
4 ohms EIA 1 kHz 0.1% THD): 1800 Watts Continuous Average Output Power Per Channel
2 ohms (EIA 1 kHz 1% THD): 2500 Watts Continuous Average Output Power Per Channel
Bridge-Mono Mode

8 ohms (FTC 20 Hz–20 kHz 0.1% THD): 3200 Watts
8 ohms (EIA 1 kHz 0.1% THD): 3600 Watts
4 ohms (EIA 1 kHz 1% THD): 5000 Watts
Other

Distortion (SMPTE-IM): Less than 0.02%
Distortion (typical):
20 Hz-20 kHz: 10 dB below rated power Less than 0.02%
1 kHz and below: full rated power Less than 0.02%
Frequency Response: 20 Hz to 20 kHz, 8 ohms, LF filter bypassed, +0/-1 dB 5 Hz to 50 kHz, 8 ohms, LF filter bypassed, +0/-3 dB
Damping Factor: Greater than 250 @ 8 Ohms
Noise (unweighted): 100 dB below rated output (20 Hz to 20 kHz, 8Ohms load)
Input Sensitivity: 1.42 Vrms for 1050 watts into 8 Ohms
Controls:
Front Panel: AC power switch, Ch. 1 and Ch. 2 gain control
Rear Panel: 10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel.
Voltage Gain 64x (36 dB) for 8Ohms load
Input Impedance: 20 kOhms balanced, 10 kOhms unbalanced
Indicators:
Power-On: Green LED
Protect: Red LED
Signal -30dB:Yellow LED
Clip: Red LED
Connectors:
Input: XLR female, each channel
TRS (1/4-inch), each channel
Barrier-strip screw terminals, each channel
Output: Binding posts and Speakon outputs (Ch. 1 Speakon wired for biamp)
Cooling: Continuously variable-speed fan, rear-to-front air flow
Amplifier Protection: Short circuit, open circuit, thermal, ultrasonic, and RF protection.
Stable into reactive or mismatched loads
Load Protection: On/off muting,DC fault output crowbar
Power Requirements: 100,120 or 240 Volts AC (±10%) 50-60 Hz (factory configured)120V models require 20 Amp,120V service and are supplied with a NEMA 5-20 plug on the cordset.
Dimensions: 19.0" (48.3 cm) wide, 5.25" (13.3 cm) tall, 15.9" (40.39 cm) overall depth
Weight: 75 lb (34.02 kg) net,

Other views of QSC RMX5050 (Click to enlarge):