Peavey Classic 30 112 Guitar Amp

PEAVEY CLASSIC30112 Details ^top

The Classic(R) 30/112 has been redesigned with an all-new chassis design, but still features the distinctive sound and circuitry of the renowned Classic(R) Series amps.This newest member of the Classic tube amp family uses the same basic preamp design as the Classic 50, with the addition of the boost switch. The 30 watt power amp, when combined with the specially-voiced 12" speaker (Combo only), creates a very powerful amplifier that’s portable enough for backstage or practice, yet loud enough to jam with a rhythm section. The dual channel preamp allows quick variation of tone— from vintage blues, to modern hard-rock and grunge tones. The boost switch is particularly useful in obtaining the more traditional “cranked-amp” tones without the harshness generated by sending too much low end to the power amp. The 30 watt power level is just the right amount for power amp chunk and sustain at a reasonable volume.

Two particularly modern additions to this amplifier are the reverb and effects loop. The reverb unit is the long-spring type found in most guitar amps since the 50's. The effects loop comes in especially handy when used with delay, chorus, and many other effects units, racks or stomp boxes—when you don’t want the associated noise of connecting them in-line with the amp. For a special treat, try plugging one of the Classic enclosures or even a 412-Peavey 6505™ cabinet into the external speaker jack. You’ll find this particular combination has plenty of “knock” in the low-end. And best of all, it’s very LOUD.

Features

* 30 watts (rms) into 16 or 8 ohms
* Four EL84s and three 12AX7s
* 12 inch Blue Marvel(R) speaker
* 2-channel preamp
* Pre- and post-gain controls on lead channel
* Normal volume control on clean channel
* 3-band passive EQ (bass, middle, treble)
* Boost switch
* Reverb level control
* Effects loop
* Footswitch selectable channel switching and reverb
* External speaker capability
* Chrome-plated chassis
* Black Vinyl covering
* Footswitch optional (not included)
* Black Vinyl or Tweed

NOTE: Please add your covering choice in the notes section of the shopping cart. Tweed or Black Vinyl

PEAVEY CLASSIC30112 Specs ^top

POWER AMPLIFIER SECTION
Four 6BQ5/EL84s with 12AX7 driver
Rated Power & Load:
30 W RMS into 16 or 8 ohms
Power @ Clipping (Typically):
(5% THD, 1 kHz, 120 VAC line)
3O W RMS into l6 or 8 ohms
(Bias must be reduced to measure.)
Frequency Response:
+0, -2 dB, 50 Hz to 15 kHz, @ 20 W RMS into 16 ohms
Hum & Noise:
No greater than 80 dB below rated power
Power Consumption:
150 watts, 50/60 Hz, 120 VAC (Domestic)
Remote Footswitch (included):
Heavy duty 1-button footswitch
PREAMP SECTION
Two 12AX7’s
The following specs are measured @ 1 kHz with the controls preset as follows:
Pre & Post (lead) @ 0
Reverb Level @ 0
Bass & Treble EQ @ 12
Middle EQ @ 0
Channel Select Out
Boost Switch Out
Nominal level is with Input Gain @ 6
Minimum level is with Input Gain @ 12
Preamp Normal Input:
Impedance: Very high Z, 470 K ohms
Lead Channel (Post Gain @ 12):
Nominal Input Level:
-40 dBV, 10 mV RMS
Minimum Input Level:
-70 dBV, 0.3 mV RMS
Normal Channel (Post Gain @ 12):
Nominal Input Level:
-17 dBV, 140 mV RMS
Minimum Input Level:
-28 dBV, 40 mV RMS
Maximum Input Level:
0 dBV, 1.0 V RMS
Equalization:
(Lead and Normal Channels)
Custom bass, middle, and treble passive-type EQ
Effects Send:
Load Impedance: 1 K ohm or greater
Nominal Output Level: -6 dBV, 0.5 V RMS
Effects Return:
Impedance: High Z, 2 M ohms
Designed Input Level: -6 dBV, 0.5 V RMS
(Switching jack provides Effects Send to Effects Return connection when not used.)
External Footswitch Function:
Reverb Defeat (when reverb control is raised)
Normal/Lead Channel Select (when Lead activated)
Speaker (Combo Only):
One 12" Blue Marvel
16 ohms

PEAVEY CLASSIC30112 Manuals ^top

Classic 30 Owners Manual (pdf)

PEAVEY CLASSIC30112 Artists ^top